Tying The Wiggle Bug

[Bob Laskodi]

Top water fishing for striped bass is about the most exciting way to hook up with Mr Striper. While I'm really not a top water expert, I have been some what disappointed with the action of most top water flies and have been searching for a quick, easy to tye fly that has a lot of action in the water. The Wiggle Bug is an interesting fly that pops, spits water, dives when retrieved, and has an enticing side-to-side action to tempt most fishies that like to eat on top. More importantly, it is a very easy to tye fly! You can vary the size and colors to suit your local game fish.
http://img.photobucket.com/albums/v11/laskodi/020e35e5.jpg
Hook: Mustad 34011 Size 3/0
Thread: UTC GSP 200 Denier, White
Body: Estaz, Pearl, Large
Throat: Super Hair, Red
Foam: Rainy's Cross Link Sheet Foam, 6MM, White
Flash: Targus Motion Flash, Pearl White
Tail: Marabou Blood Quill, White
Eyes: Doll Eyes from craft store

Step 1: Cut a 2 1/4 inch long by 3/8 inch wide piece of Rainy's 6 MM Cross Link Sheet Foam. With a sharp knife/razor blade cut a notch off one corner as shown. The notch is the "lip" of the fly. The longer the lip, the more popping, and diving action.
http://img.photobucket.com/albums/v11/laskodi/b13f10f2.jpg

Step 2: Open a hole through the center of the foam with your bodkin as shown. The hole is to allow the "lip" of the fly to pass through the hook eye. Try and get the hole centered in the foam exactly as the fly may spin if off center.
http://img.photobucket.com/albums/v11/laskodi/c087399d.jpg

Step 3: Attach GSP thread to the entire hook shank. Use a liberal amount of your favorite head cement to glue the GSP thread to the hook shank since GSP is very slick and easily spins on the shank.
http://img.photobucket.com/albums/v11/laskodi/8aea6e93.jpg

Step 4: Attach the Estaz at the rear of the hook and wrap forward to eye and secure. Make sure you leave space on both the butt and head of the fly as shown.
http://img.photobucket.com/albums/v11/laskodi/ea227c9a.jpg

Step 5: Attach about 25 strands of Super Hair to the forward section of the hook and trim to about 1/2 body length. Cut off and whip finish GSP thread at the eye of the hook.
http://img.photobucket.com/albums/v11/laskodi/1b292aba.jpg

Step 6: Take the foam strip and shove the eye of the hook through the opening created by your bodkin. The cut lip section is the top of the fly. Secure the butt end with GSP thread tyed on the rear of the hook. GSP thread is needed as the foam is quite hard and you must apply a lot of pressure to fully secure the foam. The head section is not tyed in with thread and is held in place by the hook eye. Place a drop of superglue on the tyed in foam butts and at the front hole where the hook eye sticks through. Be careful to not fill the hook eye with glue!
http://img.photobucket.com/albums/v11/laskodi/0a301887.jpg

Step 7: Take your flash material and tye in at the tail. I used Targus Motion Flash but your favorite flash material can be substituted.
http://img.photobucket.com/albums/v11/laskodi/1ce6d3cc.jpg

Step 8: Tye in a marabou blood quill by the tip. Pick a feather that has a very thin stem as you will be wrapping forward just like a dry fly hackle.
http://img.photobucket.com/albums/v11/laskodi/1912f4d3.jpg

Step 9: Wrap marabou forward to cover all butt wraps, and secure with GSP thread. Whip finish and apply a small amount of head cement to secure the whip finish threads in place.
http://img.photobucket.com/albums/v11/laskodi/cb6852f1.jpg

Step 10: Add doll eyes as shown with epoxy and go fishing! Don't forget to hang on when Mr Striper eats your fly!!!
http://img.photobucket.com/albums/v11/laskodi/020e35e5.jpg

[lee s.]

Very useful info Bob,
Great steps and photos.
Yes, top-water stripes are a hoot. But come to think of it, ANYTHING top-water is a HOOT! ;-)
....lee s.

[Fochetti]

Nice post, it would be great to see more of these with detailed steps.

[Hector Lopez]

Liked your step by step pictures! Will tie some up for a friend that loves top water action with stripers and is currently camping on the Delta for a month.

[jbird]

Can you describe how to fish this fly? Will it wiggle side to side with a long slow strip?

[JD]

This is Larry Tullis' pattern, I believe? I've always been curious how durable this fly is. With nothing but a little superglue holding the foam back at the eye, I always thought this might be a bit too fragile. What has been your experience, Bob?

[Bob Laskodi]

<<<Will it wiggle side to side with a long slow strip?>>>
I can't answer that question because I never fish long slow strips for stripers!!! ;<}
My guess would be yes, though!
I fish it strictly as a topwater bug, although I have friends who fish it on a sinking line with good results. To describe in one word how I fish it --- erratic! Fast retrieve mixed with slow retrieve, hard strips mixed with soft strips, pauses mixed with quick strips, you name it! Make the bug wiggle and dance is the name of the game with that long tail.
I don't know the origin of the pattern, but it's been around a while. Use GSP thread with superglue and it's plenty durable.

[Hairstacker]

Bob, that is a great-looking fly and an especially nice tutorial you posted -- thank you!! I'm going to have to give that one a go myself. :D